Wednesday, September 11, 2013

Multi function CNC, Pen/Laser/Extruder, 16"x20" build area

So now that I have a nice CNC mill what is the most obvious first thing that I should build? Why another CNC of course! In an age where you can 3D print a printer this comes as no surprise, but I am looking for an all aluminum build platform with all metal on metal structural junctions held together with high tension machine screws or flat out TIG welded (if I can bribe someone into letting me use the IMSE welding lab).

Here is 2D of what I am looking at so far

Side View

End View

 Blue is the base, red is the gantry, green/cyan is the sled and yellow is linear shafts. Green is not going to be a permanent fixture as this will be used 90% for a larger laser diode cutting system and the massive amount of weight is a no-no for raster engraving/burning. It will be used for experimentation with a very difficult form of printing that another club member brought to my attention but I don't want to make a fool of myself so progress will be presented when it is made.

There are really only 3 forms of aluminum in the entire thing, 1/4" plate for the gantry sides and the ends of the bed, 1" tubing (1/16" or 1/8" is yet to be decided) to hold everything in between, and probably 1/8" for the bed.

Some consideration is going to have to be made where the steppers intersect the 1" tubing but I think overall it will strengthen the gantry since the supports will be milled individually and precisely square, when the stepper is installed it should force the whole thing into square by making the horizontal bars stay parallel. It should also be noted the linear shafts will have high tension clamp on shaft collars just inside of the gantry sides so when the screws are tightened down the shafts themselves will have a load put on them adding another point of rigidity. These areas are not detailed in the drawings because this will be a one off for the most part and parts/changes will be made when the time comes.

Linear propulsion systems are  belted on the X and Y for laser speed and Z is acme lead screw for precision and a bit more head pressure. I have all of the steppers, belt gears, and the lead screw from the auction (The lead screw is actually the quill adjuster from my mill) so all I have to order is the linear shafts, brass bushings, and belts when the eBay money hits my bank account and aluminum stock when I go to KC.

Control wise I already have an Arduino Uno, 3 Pololu stepper drivers and a breakout board that I am beta testing (link found below).

Protoneer CNC Shield for Arduino

Power supply is a 12v Meanwell regulated PSU. Since the steppers are only 2.4v I turned the adjustment pot on the PSU as low as it goes, which is about 10v. Pololu drivers support active current control and actually NEED higher source voltage in order to effectively use microstepping and allow very fast seek rates when no load is applied (all the time when lasing). Still need to get them some little heat sinks so I can run them up to 2A.

The arduino and the PSU will both be mounted underneath the work surface and pockets will be cut for the arduino USB, PSU 120v chassis mount, and a large E-stop button. Cable will all be inside of cable chains printed on the Replicator 2 that belongs to the club I just joined. In the end it should be very polished, pull the USB and power cord then pick it up and go.

Electric Circuit and Controls homework beckons,

Tuesday, September 10, 2013

Auction Purchases: Items for sale and other

So here's what's for sale. I have omitted some things as it really isn't worth the time to sort and ship resistors/connectors/etc.

I live in Kansas City and go to KSU in Manhattan KS so face to face deals would be more than welcome. If you are uncomfortable dealing directly I can put stuff on eBay for you at a pre agreed buy it now price.

No reasonable offer refused, just look up retail and take a good percentage off.
__________________________________________________ _________________________

Pic 1: LEDs
8-10 High Power RGB LEDs one of which is a 3W
Mid to upper hundreds of standard power RGBs
Mid to upper hundreds of standard power Whites
sack of 8mm blue
sack of IR 5mm
sacks of various "high brightness" standard power whites and many loose
~500 "Piranha" style RGB LEDs $0.20ea

After taking this picture I still kept finding more bags of LEDs

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.

Pic 2: Steppers
These are relatively self explanatory, tinys, NEMA 17 , NEMA 23, NEMA 34

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.

The largest 3 are labeled 42-8A  in a NEMA 34 frame, these suckers are BEASTS. If I could justify it I would probably build a giant plasma table with them or a robot with rather deadly intentions. They have so much torque I almost wonder if they could drive the E-Bike...
The tub with what looks like rolls of coins is actually full of sealed skate bearings, ABEC-7 concentrically rating, 10pc per tube. Perfect for Bots or CNC.

A couple things I forgot to add to the table were 5 ball nuts for high precision ball screw linear motion systems. As with the LEDs as I keep going through the boxes I just keep finding more and more, no more big ones though. There are also 3-4 Meanwell PSUs that would be great for all but the largest steppers.

Pic 4: Micro-controllers
Here is where the fun begins, all of the bare chips shown on the left half are Atmegas and Attinys

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.

18x atmega325p-20au (SMD) $3.00
22x atmega644p-20au (SMD) $3.50
24x atmega640-16au (SMD) $4.50

22x 164 (Large format DIP) $3.25
28x atmega164p-20au (SMD) $2.50
14x atmega88-20AU (SMD) $1.75ea
5x tiny 2313 (SMD) $1.25ea
10x tiny 24 (SMD) $1.00

25x MSP430G2231 MCU
6x MSP430FG439 Low Power MCU

Also found some XMegas but I think I will be keeping them.

Boards included
Minty Boost
FM Transmitter Microphone Object sensor
devantech digital compass
2x brainstem interface module
several others I dont recognize

Also a basic beagle board not pictured. Not sure what they are worth due to competition with RasPi but taking offers


Beefy PSU, 36v 25A. Not as large as 1.8KW supply, only weighs as much as a single sack of concrete instead of two though. Only paid $16 for this bad boy and it works great other than the fan was shattered but I already had a replacement

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.

__________________________________________________ ________________________
Pic9: ICs

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.

This is the bulk of the ICs. They were all dumped in a big tub so I had to sort them out of a bunch of other stuff so that I would then sort each IC type from another. What I did was just sort 1/3 of the chips in the tray and use that to estimate the total number of chips I have.

100x Ti 07A612M SN75441one Half H Driver $1
50x Philips 74HCT04N inverter $0.15
25x MSP430G2231 MCU $1
6x MSP430FG439 Low Power MCU $5
30x 386BD Audio Amp $Offer
45x P82871SPN Signal buffer repeater I2C extender
50x L620SD Motor Controller Dual Full H Bridge
30x VNH25P30 Half Bridge Motor Controller
7x SLA7032M 2 Phase Unipolar Stepper Motor Driver
100x JC79RA LM1084 5v LDO Regulator $1.50

Pic10: Bot Parts
Pictures is labeled pretty well. Tons of bot parts for bots or CNC. Not going to go into high detail but there are ~12 IR distance sensors, 6 Line sensors, and ~8 "Photomicrosensors". And a bottle of Aspirin for when things get real tough.

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.

Pic12: Equipment

This image has been resized. Click this bar to view the full image. The original image is sized 1024x768.

Most of the good stuff at the auction went pretty high, This is stuff that came out of the large lots that I bought.
2 large DC supplies. Shortwave radio antenna kit from radio shack. Divider box has about ten different values of caps in it plus some crystals and chips I didnt check out. DC to DC "TX" PC power supply boards, Along with the irons shown I also have another half dozen Hakko 936 solder stations some with and others without pens

There you have it, let me know if anything catches your eye, yes I'm trying to make a bit o' money but I like helping others afford their own projects as well .

Happy Hackin,

Update: Life and Stuff

So I've neglected the Blog for a long time and came back to see people had actually read... and even responded to some of my posts. If you are one of those people who asked a question and are reading this I sincerely apologize and promise to do better in the future. Things have been hectic in school and I now am a student at the Electrical and Computer Engineering Technology department through Kansas State University's Salina campus. This is a huge stress reliever as I don't have to take the high level math classes and instead of electron theory I have the ability to do more applied classes which I get to build cool stuff. So going over the notable things since then I think I should start with the most exciting news.

About a month ago I came across publication for an auction site that was selling the estate of an electronics hobbyist that passed away. I am fairly familiar with this auction house as I have bought other electronics surplus stuff from them but this was hinted to as an estate auction and mixed in with a bunch of industrial equipment so most of the other bidders where not informed on what was available. In fact the only guy that was bidding against me was buying for scrap metal.

My big purchase was something that I have been wanting to buy for a crazy long time. A metal mill, and a CNC conversion at that. Grizzly G4007 8"x20" mill with full ball screw anti backlash conversion, gecko G540 drivers running rotary encoded servo motors. Pretty primo for a conversion.


The main controller is rather outdated and does not have proper Mach3 plugins so I think I will be getting a KFlop USB CNC Controller, it has 8 axis support and all I need it 4 (thinking about adding a rotary "lathe" axis) and I didnt really want to pay for the extra but it seems to be one of the best supported options.

Along with that I purchased a HUGE amount of electronics, a real robot and CNC builder's dream at pennies on the dollar. I'm hoping to sell a good portion of it and use the profit to pay off the rest of the mill (I'm lucky enough to apply for the parental loan system).

I feel like I should throw in the disclaimer that although my family owns a small business we are not rich by any means, I am 21 and for example I drive a 99 civic (NOT riced out) that I have had for the last 6 years and pay for my own gas. I am in college and pay my own bills and take out as many student loans as I can get and then pay the rest forward. I also pay for everything you will see on the blog. Out at school I make $7.50/hr at a pet store. Not poor by any means but not rich. *Sigh

Anyway I will put a post up shortly outlying all of the stuff I have for sale and other cool stuff I found, I've been selling stuff for roughly 50% off the cheapest it can be found anywhere retail unless it is stuff I think I can use for my own projects.

Time to go to work so I can pay for that KFlop :)